Enthoo EVOLV ATX TG
ATX Mid Tower
Side Panel Window
Tinted Tempered Glass
Power Supply Shroud
Front Panel USB
Motherboard Form Factor
- Micro ATX
- Mini ITX
Full-Height Expansion Slots
Half-Height Expansion Slots
Maximum Video Card Length
- 300 mm / 11.811" With Drive Cages
- 420 mm / 16.535" Without Drive Cages
Internal 2.5" Bays
Internal 3.5" Bays
- 133 points
- 30 months ago
from completed build Old Glory - Phanteks Enthoo Evolv ATX TG
One of the first reviews on amazon for this case was from me. I bought it right when it came out. Build quality is top notch. Really set the standard for aluminum at a reasonable price compared to lian li. Great looking case and they did think of a ton of options for builds. Only downside is top airflow is not the best but i am willing to sacrifice that.
- 58 points
- 34 months ago
from completed build Maverick - Z270 Formula | 1080 FTW | i7
This case was by far my favorite out of everything that I looked at, and I couldn't be happier with the purchase. It was awesome to work in, however, I did find a few struggles with the hard drive cage while trying to include a third 120mm fan near the bottom of the front intake, but once I figured that out, everything else just fell into place. Tempered glass side panels are gorgeous, and the fact that both sides are transparent, it really puts some good pressure on you to do a good job with your cable management.
- 32 points
- 27 months ago
from completed build Wonder Women
THE best looking case ever , lots of room for everything , easy cable management . Air flow is not that great but with water cooling and lots of fans no problems . Also I wish it would take E-ATX motherboard .
- 30 points
- 19 months ago
from completed build Riptide
Gorgeous case. Oh, and it’s a breeze to build in too!
- 21 points
- 34 months ago
from completed build Virtue
This case is absolutely beautiful for putting a custom build in. The screws holding the 2 tempered glass side panels on are very strong and secure feeling. They have very good rubber grommets on them to make sure there is no metal on glass contact when tightening them down. One thing I'm not a big fan of is the fact you can't put fans on the outside of the sliding rail on the top of the cage. For me that sliding rail didn't make much sense because I didn't use it but for someone it's probably a nice feature. When it comes to mounting a rad in the front of the case I was rather bothered that I had to remove not only the plate covering the hard drives but that I also had to remove the mounting hardware in all. So after its done you can't mount your hard drives in the front because of that. It would of been nice for there to be different mounting hole to put the rad up higher in the front but oh well. The basement only partly covering the power supply is a nice touch in my opinion. Be very careful when it comes to doing cable management. when it comes to doing management do it as you go. DO NOT wait till the end and just manage it then, you'll be hating life. Once it's all said and done, after its all built and put on its pedestal this thing is gorgeous to look at. Tempered glass is beautiful to look at especially when you have a little led lighting in it.
- 21 points
- 31 months ago
from completed build Dat Glass (Evolv ATX TG)
Glass, and a lot of it. This is my first Phanteks case and after this build, Phanteks will probably be my go to case manufacture. The case looks sleek and with just the right amount of RGB's can really make it pop.
Cons: -The side panel mounting mechanism could be different as it's kind of a hassle to unscrew the four thumb screws while making sure it doesn't slide off the side. But how often are you really going to be taking the panels off?
-I wish the velcro straps in the back were a tad longer.
-Airflow isn't really that great at the top but I knew that going in. Aesthetics over performance sometimes wins.
- 17 points
- 11 months ago
from completed build Deep Learning Research Build
Spacious and beautiful case with its sleek space gray aluminum design. Gives you everything you need to get your PC up and running and provides neat grommets and built in cable management solutions.
- 11 points
- 15 months ago
from completed build Pexus EX
Love this tower. Lots of fan potential very 360mm rad friendly. It’s a big boy though and it gets heavy quick weighing nearly 14 pounds stock. Good looking case. If you can find it on sale it’s a great price too
- 10 points
- 32 months ago
from completed build New build after almost 10 years
When I first saw this case I knew I had to have it, It's by far the most beautiful case I could find. The build, other than the cooler as mentioned above, went easy as can be. The only negative is that this case despite having tons of space for fans and 3 included 140mm fans, is a little restrictive on the airflow due to the design. It's not bad, just not great, if cooling is your number one priority this may not be the case for you. Again totally adequate, just not great.
- 9 points
- 16 months ago
from completed build ¨£%µXC¨S£Q% are the only word to Describe My Final PC.
Very Disapointed about this tower, i search for so long for finding a case like this one and for 230 € i think it's over priced as F%ck. - We can only put a 120 mm Water cooling in the top or with a 1400 you need to cut the hdd Bay.
- View Compatible CPU Coolers
- View Compatible Fan Controllers
- View Compatible Motherboards
- View Compatible Optical Drives
- View Compatible Power Supplies
- View Compatible Sound Cards
- View Compatible Storage
- View Compatible Video Cards
- View Compatible Wired Network Adapters
- View Compatible Wireless Network Adapters