That doesn't mean its not compatible. The qualified vendor list is for ram the mobo manufacturer tested and can guarantee that it works correctly. I honestly wouldn't worry with a higher end motherboard like an ROG or really just any motherboard that isnt a cheap pos(you can usually tell by what the colors and price of it is). That stuff, from what I saw when I was looking at that, was that it's only a problem with say a cheapo $50 asrock motherboard. Also get an rog b450 instead of b350, it's backwards compatible with any ryzen architect and will help overclock your cpu better.
sorry for the late reply and no. i had to use my phone for those pics bc my professional camera was lost at the time. The zones blend so it actually looks decent in person. However, it is noticeable enough though that i wish i just got tforce nighthawks or gskill trident z instead. these arent worth it. I say the pics that i had my flash on for, are very close to what its like.
How much was the custom Waterloop? I plan on building a pc almost like this one. Also I noticed you don’t have an exhaust fan
Just make sure it has the label on the box, top right corner
It comes Ryzen 2000 ready
I’m getting that it’ll be fine since it’s not detached or anything. It’s just a small imperfection with the glue, which holds the cpu together, and shouldn’t bring any concerns. I’d guess it’s from me trying to heat up the thermal paste when my cpu was stuck to the heatsink, but at the same time, it’s an excess so it must’ve been on AMD. Either way, there’s no issue now so thank you
I believe it might be the sealant for the cpu. I don’t see why it wouldn’t be a manufacturer mistake and I never yanked up on the cpu
Look at the last image.(I couldn’t find a way to make a url for the pic) I’m not sure if that’s the seal since i see a slither of it around the whole cpu, but I wanna make sure that I didn’t break it
Yes. I’m not sure about others like gigabyte fusion and so on.
This article shows there’s a 13C difference but that’s also the prism not going past 1600rpm and that’s silent for a prism while the stock cooler is louder and can’t keep up. I’ll personally test it myself when I switch the thermal paste out on my prism and that’ll be in 2 days
Yeahh I was looking and decided to buy Noctua NT-H1 and I was able to lower my idle about 7C after lowering my voltage. I’ll probably have an idle around 37-39C once I use the better thermal paste
I bought it off eBay. I saw it could run as good as Noctua fans but this is more attractive. I’m getting better thermal paste and it performs very well. A lot better than the stock wraith cooler
What I noticed is that at stock setting(3.6Ghz). My CPU cooler runs at 1200rpm and my temps look to be 37C. However my voltage is already at 1.4V and I’m not sure if this may be why.
No. Some lights like that can be normal so I say your best bet is to look in the manual and if you don’t find anything, contact your motherboard manufacturer. You’ll find out what’s wrong
It was preapplied thermal paste and it’s mounted properly. My case is very open and since I don’t have a graphics card yet, I was expecting my thermals to be a bit better since my fans are more directed towards my cpu
I am measuring in celcius and I was looking around at what people’s temps are for idle with the stock cooler. Im thinking I might have to just lower my overclock or ramp up my cpu cooler a bit
I’ve never experienced this problem since I’m not using SLI. However, I recommend trying to use only one gpu to boot your pc. If it still won’t boot, the problem isn’t your gpu. Check the wiring for your cases buttons incase one of them is loose or something. Just slowly try all possible ways to figure this out. Don’t give up on it
I hope he isn’t trying to sell a pc on pcpartpicker
I personally would say there’s not much of a difference with how you mount the radiator. The pump will still have to pump the water with almost the same pressure either way, and you should just chose how you’d want the tubes to be arranged. If you’re still on edge, try looking at more builds and go off what other people are generally doing with their AIO
I’m building a pc that uses the exact motherboard and cooler. I’m just going with a 2400g until prices for GPUs go closer to msrp and it’s an excuse to build the pc now instead of a year later. Was there any issues you had with the cpu cooler and would you know if any Team Force ram would work with this motherboard? Specifically T-force delta RGB